
Thank you for reading our post, please rate this article at the end.
Reading Time: 6 minutesLast Updated on November 15, 2026 by Paul Clayton
The 3 numbers on ATV tires give the tire’s size in inches, in the order height x width – rim diameter. On a tire marked 25×8-12, the first number (25) is the overall height or diameter of the inflated tire, the second (8) is the tread width, and the last (12) is the diameter of the wheel it fits. The dash means bias-ply construction; an “R” in its place, as in 26x9R12, means a radial tire.

Table of Contents
Key Takeaways
| Marking (example 25×8-12) | Meaning | Why it matters |
|---|---|---|
| 25 | Overall tire height (diameter) in inches | Ground clearance, gearing, speedometer and clutch load |
| 8 | Tire width in inches | Traction, flotation, steering effort and fender clearance |
| – (dash) | Bias-ply construction | Tough sidewalls, flexible ride at low pressure |
| R | Radial construction | Smoother ride and longer tread life, especially on hard surfaces |
| 12 | Rim (wheel) diameter in inches | Must exactly match your wheel |
| Typical ATV pressure | About 3 to 8 psi for most ATVs | Always use the owner’s manual or vehicle label, not the sidewall maximum |
What Do the 3 Numbers on ATV Tires Mean, One by One

1. Tire Height (Overall Diameter)
The first number is how tall the tire stands when mounted and inflated to its rated pressure. A 25-inch tire measures about 25 inches from the ground to the top of the tread. In practice, many tires measure slightly under their nominal size, often by about half an inch, so compare actual measurements in reviews if fender clearance is tight.
Taller tires raise ground clearance by half of the increase (a tire 2 inches taller lifts the axle about 1 inch), roll over rocks and ruts more easily, and change your effective gearing.
2. Tire Width
The second number is the width of the tire’s tread section. Wider tires spread the machine’s weight over more area, which helps in sand, mud and snow, but they increase steering effort and can rub on suspension parts or fenders. Many ATVs use narrower tires in front and wider ones in the rear, for example 25×8-12 front and 25×10-12 rear.
3. Rim Diameter
The last number is the diameter of the wheel the tire fits, in inches. This number must match your wheel exactly: a 12-inch tire only fits a 12-inch rim. Common ATV and UTV rim sizes are 9, 10, 11, 12 and 14 inches. Larger rims usually mean a shorter sidewall, which sharpens handling but gives less cushion and more risk of rim damage on rocks.
Dash vs R: Bias-Ply or Radial
The symbol between the width and rim size tells you how the tire is built. A dash (25×8-12) means bias-ply, with fabric cords crossing at angles; these tires have stiff, puncture-resistant sidewalls and a flexible carcass that grips well at very low pressures. An R (26x9R12) means radial, with cords running across the tire; radials ride more smoothly, run cooler and last longer on hard-packed trails and gravel roads, and are common on side-by-sides.
Metric ATV Tire Sizes Explained
Some ATV and many UTV tires use a metric format like car tires, for example 205/80R12:
- 205 is the width in millimeters (about 8.1 inches).
- 80 is the aspect ratio: sidewall height as a percentage of width (80% of 205 mm is about 164 mm, or about 6.5 inches).
- R12 means radial construction on a 12-inch rim.
To estimate overall height, add the rim diameter to twice the sidewall height: 12 + (2 x 6.5) = about 25 inches. So a 205/80R12 is roughly equivalent to a 25x8R12.
Other Markings on an ATV Tire Sidewall
| Marking | Example | Meaning |
|---|---|---|
| AT prefix | AT25x8-12 | All-terrain vehicle tire; not for highway passenger use |
| Ply rating | 6-ply rated | Strength and puncture resistance; common range 2 to 8 ply |
| Load index and speed symbol | 43F, 48J | Maximum load per tire and maximum speed (F about 50 mph, J about 62 mph) |
| Max pressure | Max 7 psi | Highest safe pressure, mainly for seating the bead; not the riding pressure |
| DOT date code | Four digits like 1523 | Week and year of manufacture (week 15 of 2023) |
| Rotation arrow | Arrow on sidewall | Direction the tire must roll; directional tires mounted backward lose traction |
How to Choose the Right ATV Tire Size

- Read your current tires and the owner’s manual for the stock front and rear sizes.
- Stay close to stock for the best handling and drivetrain life. Going up about 1 to 2 inches in height is usually fine on most utility ATVs.
- Keep front and rear heights matched on 4×4 machines. A mismatch can strain the front differential.
- Check clearance at full steering lock and full suspension compression.
- Match the tread to your terrain (see below).
- Consider weight. Bigger, heavier tires add rotating mass that the engine and CVT belt must turn.
Upsizing warning: Tires much larger than stock reduce effective gearing, which can overheat or burn CVT belts and clutches, especially in mud or when towing. They also raise the center of gravity and make rollovers more likely on side hills. Large upgrades often need a clutch kit, lift kit or gear reduction. For pulling or plowing, see what size ATV to plow snow.
Tire Types by Terrain
- All-terrain or trail: Medium lugs for dirt, gravel and light mud. The best all-round choice for most riders.
- Mud: Tall, widely spaced lugs (often 1 inch or deeper) that clean out as they spin; rough and noisy on hard ground.
- Sand: Paddle-style rear tires and ribbed front tires for dunes; poor on hard ground.
- Rock or hard-pack: Tighter tread and tougher, higher-ply construction for sharp rock.
- Snow: Softer compounds and siped tread; often combined with chains or tracks in deep snow.
- Race or sport: Lighter tires with low profiles for tracks and motocross-style riding.
Retailers such as Pure Offroad let you filter ATV tires by these exact size numbers.
ATV Tire Pressure and Maintenance

ATV tires run at very low pressures, typically about 3 to 8 psi depending on the model, front versus rear and the load. That is too low for a normal car gauge to read accurately, so use a low-pressure gauge (0 to 15 or 0 to 20 psi). Uneven pressures side to side make the ATV pull and can affect stability.
- Check pressure cold, before every ride.
- Inspect for cuts, sidewall bulges and embedded thorns or nails.
- Replace tires when lugs are worn down, chunked or cracked, or when the rubber shows age cracking, regardless of tread left.
- Wash off mud and chemicals; store out of direct sunlight.
- Carry a plug kit and small inflator on trail rides. Plugs work for tread punctures; sidewall damage means replacement.
Proper gear matters as much as tires; see what to wear when riding an ATV. Side-by-side owners can compare replacement timing in when to replace UTV tires, and if you are still choosing a machine, read what kind of ATV should I get.
3 Numbers on ATV Tires FAQ

Is the first number on an ATV tire the height or the width?
In the inch format (25×8-12), the first number is height and the second is width. In the metric format (205/80R12), the first number is width in millimeters. Do not mix the two systems up.
What does 26×9-12 mean on an ATV tire?
The tire is about 26 inches tall and 9 inches wide, is bias-ply (dash), and fits a 12-inch wheel.
Can I put 26-inch tires on an ATV that came with 25s?
Usually, yes. A one-inch increase rarely causes problems on utility ATVs. Check fender and suspension clearance, and keep front and rear sizes proportionate.
Why do my front and rear ATV tires have different sizes?
Many ATVs use narrower front tires for lighter steering and wider rears for traction. The heights are usually the same or very close, and the rim sizes may differ.
How long do ATV tires last?
It varies widely with terrain and riding style; many riders get roughly 1,000 to 3,000 miles, with rocky trails and pavement wearing tires fastest. Replace them sooner if they show sidewall cracks or damage.
Final Thoughts
The 3 numbers on ATV tires are height x width – rim diameter, all in inches, with a dash for bias-ply or an R for radial. Match the rim number exactly, keep height close to stock unless you are ready for clutch and gearing changes, pick a width and tread for your terrain, and set pressure from the manual with a low-pressure gauge.
Resources
- Tire and Rim Association, sizing and load standards
- ATV manufacturer owner’s manuals for tire size and pressure
- ATV tire manufacturer sidewall and fitment guides
- Specialty Vehicle Institute of America (SVIA), ATV safety information




