
Thank you for reading our post, please rate this article at the end.
Reading Time: 4 minutesLast Updated on November 17, 2026 by Paul Clayton
How to waterproof plywood: seal every face and especially every edge with a waterproof coating such as penetrating or laminating epoxy, an exterior primer and paint system, or a quality water-repellent sealer, then protect it from UV and recoat as it wears. For boats, epoxy encapsulation topped with marine paint or varnish is the most durable method.
Plywood is made of thin wood veneers glued together. Water soaks into exposed edges and end grain, causing swelling, delamination, rot and mold. Even marine plywood, which uses waterproof glue and has few voids, is not waterproof on its own and still needs a protective finish.

Table of Contents
Key Takeaways
| Use | Best Waterproofing Method | Notes |
|---|---|---|
| Boat floors, transoms and hulls | Epoxy encapsulation plus marine paint or varnish | Epoxy needs a UV-protective topcoat |
| Outdoor projects (sheds, signs, planters) | Exterior primer and paint, or exterior sealer | Use exterior-grade plywood |
| Decks and wet floors | Liquid rubber or waterproofing membrane, or epoxy | Seal fastener holes and seams |
| Indoor damp areas | Penetrating sealer, polyurethane or paint | Keep edges sealed |
| Every method | Seal all edges and cut ends first | Edges absorb the most water |
Choose the Right Plywood First
- Interior plywood: not suitable for wet use even if coated.
- Exterior-grade plywood: made with water-resistant glue; fine for most outdoor projects when painted or sealed.
- Marine plywood: waterproof glue and void-free plies, the right choice for boats. See marine plywood alternatives if it is hard to find or too costly.
Waterproofing Methods Compared
Epoxy Encapsulation
Epoxy resin soaks into the wood surface and cures into a hard, waterproof barrier. It is the standard for boat work. The catch is that epoxy breaks down in sunlight, so it must be covered with paint or a UV-resistant varnish.
Exterior Primer and Paint
A quality exterior primer followed by two coats of exterior paint gives good protection for outdoor projects at low cost. It needs repainting as it wears.
Penetrating Sealers and Oils
Water-repellent sealers soak in and keep the natural wood look. They are easy to apply but need reapplying more often than paint or epoxy.
Polyurethane and Spar Varnish
Clear film finishes protect while showing the grain. Use spar or marine varnish outdoors because it flexes and resists UV better than interior polyurethane.
Liquid Rubber and Membranes
Roll-on rubber coatings and waterproofing membranes are popular for decks, roofs and floors that see standing water. Follow the maker’s coverage and cure times.
How to Waterproof Plywood Step by Step
- Cut and drill first: do all cutting, shaping and drilling before sealing so no raw wood is left exposed.
- Dry the wood: plywood must be dry before coating. Store it under cover and off the ground.
- Sand: lightly sand with around 80 to 120 grit to remove mill glaze and give the coating something to grip, then wipe away dust.
- Seal the edges: give the edges and end grain extra coats, since they absorb the most water.
- Apply the main coating: brush or roll thin, even coats over both faces, following the label’s recoat times.
- Topcoat: add paint or UV-resistant varnish over epoxy, or extra coats of sealer.
- Seal fasteners: bed screws in sealant and seal any new holes.
- Maintain: inspect yearly and recoat worn spots before water gets in.
How to Waterproof Plywood on a Boat

Plywood is common in boat floors, transoms and pontoon decks. Learn more about materials in what boat decks are made of. To protect it:
- Remove and clean: take out hardware, clean off dirt and old finish, and let the wood dry completely.
- Fill: fill holes, gaps and damaged areas with thickened epoxy.
- Encapsulate: apply two or three coats of marine epoxy to all faces and edges, recoating within the maker’s window or sanding between coats if it has fully cured.
- Protect: finish with marine paint, non-skid deck coating or varnish. If you lay carpet or vinyl over it, use a marine adhesive. See can bass boat carpet get wet for flooring tips.
A sealed deck lasts much longer; see how long a pontoon deck lasts for signs it needs replacing.
Products to Consider
Popular options include marine epoxy systems, SEAL-ONCE wood sealers, TotalBoat marine finishes and penetrating sealers, and deck coatings such as DeckWise WiseCoat. Choose a product rated for the conditions your plywood will face and follow the label exactly.
Safety warning: epoxies, solvents and many sealers give off fumes and can irritate skin and lungs. Work with good ventilation, wear nitrile gloves and eye protection, and use a respirator for solvent-based products and when sanding cured epoxy.
How to Waterproof Plywood FAQ

What is the cheapest way to waterproof plywood?
For outdoor projects, a good exterior primer and paint is usually the most affordable durable option. Do not rely on PVA wood glue as a waterproof coating; most PVA glues are not waterproof.
Is marine plywood waterproof?
Marine plywood uses waterproof glue and resists delamination, but the wood itself still absorbs water. It needs a sealer, paint or epoxy coating for long life.
How long does waterproofed plywood last?
With a well-maintained coating and sealed edges, plywood can last many years outdoors. Recoat when the finish cracks, peels or wears thin.
Can you waterproof plywood with epoxy?
Yes. Epoxy is one of the best ways to waterproof plywood, especially on boats. Always cover it with a UV-resistant paint or varnish if it will see sunlight.
How do you dry out wet plywood?
Remove the source of water, raise the plywood so air can circulate on all sides, and use fans or a dehumidifier. Let it dry fully before sealing, or the coating may fail.
Final Thoughts
Knowing how to waterproof plywood comes down to choosing the right grade, sealing every edge and covering it with a coating suited to the job. Epoxy plus a UV-protective topcoat is best for boats, while exterior paint or sealer works for most outdoor projects. Inspect and maintain the finish, and your plywood will last far longer.
Resources
- APA – The Engineered Wood Association
- USDA Forest Products Laboratory Wood Handbook
- Epoxy and marine coating manufacturer application guides




