
Thank you for reading our post, please rate this article at the end.
Reading Time: 3 minutesLast Updated on October 28, 2026 by Paul Clayton
To replace RV wall paneling, find and fix the leak that damaged it first, remove trim and the damaged panel, let the wall cavity dry completely, replace any rotted framing or insulation, then cut a new panel to fit and attach it with construction adhesive and staples or screws before reinstalling the trim. Most RV interior walls are thin 1/8-inch vinyl- or paper-covered lauan plywood, so matching panels are available from RV parts suppliers. A single panel is a weekend DIY job; laminated (bonded) walls with delamination usually need a professional.

Table of Contents
Key Takeaways
| Topic | Key takeaway |
|---|---|
| Why replace | Water damage, stains or a dated look |
| Find the cause | Fix leaks before replacing panels |
| Materials | Lightweight luan or RV-specific paneling |
| Tools | Pry tools, adhesive and staples |
| Finish | Trim and seal edges |
Watch: RV Wall Panel Replacement
Before You Start: Know Your Wall Type
| Wall construction | How to tell | Repair difficulty |
|---|---|---|
| Stick and tin (framed) | Wood or aluminum studs, insulation, thin interior panel, aluminum siding | Easiest; panels come off individually |
| Laminated / bonded | Smooth fiberglass exterior; interior panel bonded to foam and studs | Hard; delamination usually needs a pro |
Learn more in what RV interior walls are made of.
Tools and Materials
| Materials | Tools |
|---|---|
| Replacement wall panel (1/8-inch, matching finish) | Oscillating multi-tool or utility knife |
| Construction adhesive suitable for paneling | Staple gun or screwdriver |
| Staples, screws or brads | Pry bar and putty knife |
| Replacement trim or molding | Tape measure, straightedge, pencil |
| Wood for framing repairs, insulation | Moisture meter |
| Sealant for the exterior leak point | Fan or dehumidifier for drying |
How to Replace RV Wall Paneling, Step by Step

1. Find and fix the source
Stains and soft paneling are almost always caused by a leak around windows, roof seams, vents, the AC unit or exterior trim. Reseal it first. See RV air conditioner leaks when it rains and RV roof replacement.
2. Remove trim and fixtures
Take off trim, outlet covers, shelves and anything mounted to the panel. Label screws.
3. Remove the damaged panel
Cut out the damaged area along studs or pull the whole panel. Go slowly; the panel is thin and wires may run behind it.
4. Inspect and dry

Check studs and insulation with a moisture meter. Replace rotted framing and wet insulation; see RV insulation. Let everything dry completely, using fans or a dehumidifier.
5. Measure and cut the new panel
Measure the opening carefully, including cutouts for outlets and windows. Cut the panel slightly undersized so it fits without bowing, since trim will cover small gaps.
6. Install

Apply adhesive to the studs, press the panel into place, and fasten with staples or small screws along the edges and studs. Wipe off excess adhesive.
7. Reinstall trim and fixtures

Replace trim, outlets and shelving. Caulk seams where needed.
Tips for a Better Result
- Take a sample to match the finish, or replace a whole wall for a uniform look.
- Consider wallpaper, peel-and-stick panels or paint if you can’t match the pattern.
- Keep panels flat and acclimated to the RV’s temperature before installing.
- If the outer wall is bubbling, you may have delamination; get a professional assessment.
Frequently Asked Questions
What are RV walls made of?
Usually thin lauan plywood with a decorative vinyl or paper finish, over wood or aluminum framing and insulation.
Can I paint RV wall paneling instead of replacing it?
Yes, if it’s sound. Clean it, use a bonding primer made for vinyl or glossy surfaces, then paint.
How much does it cost to replace an RV wall?
DIY panel replacement can cost under a few hundred dollars. Professional repairs with framing or exterior work cost much more.
Does insurance cover water-damaged RV walls?
Usually not, because slow leaks are considered maintenance issues.
Final Thoughts
Replacing RV wall paneling is a manageable DIY project. Fix the leak first, use lightweight materials and take your time with trim and seams.
Resources
- RV manufacturer construction information
- Paneling and adhesive manufacturers’ instructions




