
Thank you for reading our post, please rate this article at the end.
Reading Time: 3 minutesLast Updated on October 29, 2026 by Paul Clayton
To locate your UTV center of gravity, weigh the front and rear axles and the left and right sides on scales, measure the wheelbase and track width, calculate where the weight balances, then raise one axle and reweigh to find the height. The center of gravity, or CG, is the point where the vehicle’s weight balances. A lower CG makes a UTV more stable and less likely to roll over, which is why lifts, roof racks and high cargo loads matter.

Table of Contents
Key Takeaways
| Measurement | How to find it |
|---|---|
| Front-to-rear position | Rear axle weight ÷ total weight × wheelbase, measured from the front axle |
| Side-to-side position | Right side weight ÷ total weight × track width, measured from the left wheels |
| Height | Raise one axle a known amount and measure the weight shift |
| Tools | Vehicle scales or four wheel scales, tape measure, jack or lift |
| Lower CG | More stability and less rollover risk |
6 Easy Steps to Locate Your UTV Center of Gravity
Step 1: Prepare the UTV
Park on a level surface, set tire pressures to spec, fill fluids and fuel as you normally ride, and decide whether to measure empty or with a driver and gear.
Step 2: Measure Wheelbase and Track Width
Measure from the center of the front hub to the center of the rear hub for wheelbase, and from tire center to tire center across an axle for track width.
Step 3: Weigh Each Axle and Side
Use corner scales or a vehicle scale to record front axle, rear axle, left side and right side weights. Add front and rear for total weight.
Step 4: Calculate Front-to-Rear Position
Divide rear axle weight by total weight and multiply by the wheelbase. That gives the distance behind the front axle. For example, if 55% of the weight is on the rear and the wheelbase is 90 inches, the CG is about 49.5 inches behind the front axle.

Step 5: Calculate Side-to-Side Position
Divide right side weight by total weight and multiply by the track width to find the distance from the left wheels. Most UTVs sit close to center, but a single driver shifts it.
Step 6: Find the CG Height
Raise the rear axle a measured height, then reweigh the front axle. The extra weight on the front, along with the tilt angle, wheelbase and wheel center height, lets you calculate CG height. Use a safe lift; two-post lifts from NA Auto Equipment are one option for shops. Many owners have a shop do this step.
How Can You Change Your UTV’s Center of Gravity?
- Lower it: Keep heavy gear low and centered; avoid big roof loads.
- Widen it: Wider track kits or wheels with more offset improve side stability.
- Be careful with lifts: Lift kits and taller tires raise the CG and rollover risk.
- Balance the load: Spread weight evenly side to side.

Why the Center of Gravity Matters
A high CG makes side-hilling, fast turns and uneven terrain riskier. Knowing your UTV center of gravity helps you set up suspension, place cargo and judge slopes. Always wear seat belts and helmets, and keep arms and legs inside. Learn more in how fast side-by-sides go, electric UTV ownership basics and why UTV insurance is so high.
FAQ: UTV Center of Gravity
Can you calculate the center of gravity without scales?
Not accurately. Bathroom scales can estimate small loads, but vehicle or corner scales are best.
Does a lift kit raise the center of gravity?
Yes, lift kits and taller tires raise the CG and can reduce stability.
Where is the center of gravity on most UTVs?
Usually near the middle of the vehicle, slightly toward the rear where the engine sits.
How do I make my UTV more stable?
Keep loads low, widen the stance and avoid unnecessary lift.
Final Thoughts
Finding your UTV center of gravity takes scales, a tape measure and simple math. Knowing it helps you load smarter, modify safely and ride with more confidence.
Resources
- NASA Glenn Research Center, center of gravity basics
- Recreational Off-Highway Vehicle Association, safety guidance




